In this tutorial, an isolated Flyback converter is designed which means the input and output have different ground. The Flyback converter designed in this project will have an adjustable output between 12V DC and 5V DC. Once the circuit is designed and assembled, the value of the output voltage and current will be observed using a multimeter. The start screen of the tool shows 20 of the most common power supply topologies to choose from. I will explain the key features of a topology window on the basis of a flyback converter. On the left side, we specify our input parameters. Our input voltage range for this design is between 27 and 60 volts. Nominal input is 48 volts. DCM Flyback 6 Design Note DN 2013-01 V1.0 January 2013 III. DCM Flyback Design Equations and Sequential Decision Requirements STEP 1: Define and determine system requirements: Every SMPS design starts in determining the system requirements and specifications. The following parameters need to be defined and determined. Parameters Descriptions. PSpice simulates the circuit, and calculates its electrical characteristics. If we need a graphical output, PSpice can transfer its data to the Probe program for graphing purposes. Also Pspice is a simulation program that models the behavior of a circuit. And Pspice is a Product of the OrCAD Corporation and the student version we are using is. 2 AC Modeling of Power Stage in Flyback Converter 1.1 How it Works In a flyback converter, when the current ramps up in the primary, energy is built up in the transformer core. When the FET switches off, this energy is dumped into the secondary, allowing current to flow in the secondary, so the primary current collapses immediately to zero.

Flyback Converter Design In Pspice Tutorial For Beginners
Flyback Converter Design In Pspice Tutorial
Flyback Converter Ltspice
Flyback Converter Design In Pspice Tutorial Free
Flyback Converter Design In Pspice Tutorials
Flyback Converter Design In Pspice Tutorial Pdf

Course-PM

ENM061 Power electronic converters lp2 HT20 (7.5 hp)

Course is offered by the department of Electrical Engineering

Contact details

Lectures: Mebtu Beza (mebtu.beza@chalmers.se), Tel: 031-772 1617, Room 3519

Tutorials: Sepideh Amirpour (sepideh.amirpour@chalmers.se), Tel: 031-772 1628, Room 3566

Pspice exercises: Anton Kersten (kersten@chalmers.se), Tel: 031-772 1638, Room 3539

Anant Narula (anant.narula@chalmers.se), Tel: 031-772 1655, Room 3535

Junfei Tang (junfei.tang@chalmers.se), Tel: 031-772 1663, Room 3544

Vineetha Puttaraj (vineetha@chalmers.se), Tel: 031-772 6755, Room 2544

Flyback Converter Design In Pspice Tutorial For Beginners

Mostafa Kermani (mostafa.kermani@chalmers.se ), Tel: 031-772 1951, Room 3531

Practical labs: Anant Narula (anant.narula@chalmers.se), Tel: 031-772 1655, Room 3535

Meng-Ju Hsieh (mengju.hsieh@chalmers.se ), Tel: 031-772 1650, Room 3510

Vineetha Puttaraj (vineetha@chalmers.se), Tel: 031-772 6755, Room 2544

Flyback Converter Design In Pspice Tutorial

Robert Karlsson (robert.karlsson@chalmers.se), Tel: 031-772 1646, Room 3564

Introduction

Power electronics deals with the conversion of electrical energy by applying solid state electronics. Power electronic converters can be applied in many different areas such as computers, electric vehicles and power systems. The course presents an introduction to the different circuits used to convert and control electrical energy. It also covers methods for designing converters which in combination with selection of suitable converter topologies, power semiconductors and passive components will give the students a basic knowledge of power electronic converters.

Course purpose

The main goal of the course is to make the students familiar with the operating principles of the most common power electronic converter topologies. Basic converter design, analysis of wave-shapes and efficiency calculations are among the items that the students will be able to perform after having participated in the course. The students will perform both simulations using Cadence PSpice as well as experimental work on real DC/DC-converters. The course also lays the foundation for the continuation course 'ENM070 - Power Electronic Devices and Applications'. The items treated in the course are also useful for engineering work in many different areas, e.g. design of power supplies, electric drive systems or power system applications.

Schedule on TimeEdit:

Course literature

Mohan, Undeland, Robbins, Power Electronics - Converters, Applications and Design, Wiley 2003, 3^rd ed.

Extra handouts will be uploaded to the course page in canvas during the course.

Course content and organization

Lectures and tutorials:

Review: electric and mathematic prerequisites, voltage and current relations for passive components, mean and RMS-value, Fourier analysis.
Active and passive components: diodes, thyristors, MOSFETs, GTOs, IGBTs, inductors, transformers and capacitors.
DC/DC converters without isolation: buck, boost, buck-boost and the H-bridge converter.
DC/DC-converters with isolation: flyback, forward, half-bridge, push-pull and the full-bridge converter.
DC/AC-generation: single-phase and three-phase AC-generation, square-wave and PWM-modulated inverters, multilevel inverters.
Diode rectifiers: single- and three-phase diode rectifiers with continuous and discontinuous DC-side current.
Thyristor converters: single- and three-phase thyristor rectifiers with varying DC-side load.
Converter enhancements: dynamic modeling, controller design, and improved configurations
Heat distribution and life-time: Loss calculations, thermal calculations, cooling requirements and component life-time.

Laboratory experiments (compulsory):

All home assignments must be prepared before each lab. The lab-PM can be downloaded from the course website at least one week in advance of each occasion.

Flyback Converter Ltspice

Buck converter
Flyback converter

PSpice assignments (compulsory):

All home assignments must be prepared before each occasion. The simulation files can be downloaded from the course website one week in advance of each occasion.

A basic power electronic circuit
Buck and Boost converter
Flyback converter
Single-phase inverter
Three-phase inverter
Single- and three-phase diode rectifier
Converter enhancements: Loss analysis and control

Before each PSpice occasion (12.30-13.15) there is an additional time slot for approval of previously completed PSpice tasks (location - check signedup group). Please use this to avoid crowding during the lab occasions.

Flyback Converter Design In Pspice Tutorial Free

The course consists of approximately:

18 lectures (2 x 45min)
13 tutorials (2 x 45min)
2 practical laborations (4h)
7 PSpice computer assignments (2h)

Changes made since the last occasion

Lectures and tutorials will be online

Learning objectives and syllabus

Learning objectives:

Determine Fourier components and total harmonic distortion (THD) for basic current and voltage wave-shapes.
Recognize the operating principle of the most common active components (e.g. diode, thyristor, IGBT, and MOSFET) as well as the most common passive components (e.g. capacitors, transformers and inductors).
Explain and exemplify how pulse width modulation (PWM) works. Describe the purpose as well as the means to control the desired quantity and recognize the need for a controller circuit within the power electronic converter.
Analyze and perform analytical calculations of ideal DC/DC converters such as the buck, boost, buck-boost, flyback and the forward conver